flexiblefullpage - default
interstitial1 - interstitial
Currently Reading

6 Tips for Specifying and Installing Windows and Doors

Advertisement
billboard -
Windows & Doors

6 Tips for Specifying and Installing Windows and Doors

Improper or insufficient design details and shoddy installation of windows or doors can lead to air infiltration, moisture intrusion and poor overall performance.


By David Barista June 30, 2009
This article first appeared in the PR July 2009 issue of Pro Remodeler.
Sidebars:

Avoid These Common Installation Mistakes

When it comes to controlling moisture and increasing energy efficiency in homes and buildings, windows and doors are among the most vital components in construction. Improper or insufficient design details and shoddy installation can lead to air infiltration, moisture intrusion and poor overall performance.

 



Photo: Pella Windows and Doors

To promote consistent, high-quality installations of windows and doors, the American Architectural Manufacturers Association has issued a 317-page installation manual geared toward the commercial building market. Lessons learned here are applicable to the remodeling industry as well. And in this economy, many remodelers are taking on replacement projects in commercial and multifamily construction. The publication, AAMA Standard Practice for the Installation of Windows and Doors in Commercial Buildings, addresses the installation of window systems and exterior glass doors — including hinged and sliding-glass doors — for both new construction and replacement projects.

The manual offers hundreds of how-to tips, lessons learned and advice on designing, specifying and installing window and door systems. We’ve highlighted six of the best tips for remodelers below; see the sidebar for more errors to avoid.

1. Install only those products designed to meet the performance levels expected on the job. Comparing the water performance capabilities of the products intended for the job with the project specifications can greatly reduce the potential for water damage due to improper product selection. Use products only on projects that have performance requirements less than, or at most equal to, the rated performance of the product.

“Where products are subjected to increased risks of wind-driven rain events, they will typically be expected to have achieved a higher design pressure (DP) rating and water penetration resistance test,” says Ken Brenden, AAMA’s technical standards manager. “All products have limitations when it comes to their performance ratings. Placing a product with a relatively low DP and water resistance rating in a structure located in an extreme weather environment will certainly lead to problems.”

2. Make sure to rebalance HVAC systems when installing energy-efficient windows and doors in existing structures. When new energy-efficient windows and doors are installed in existing buildings, the HVAC system should be rebalanced to accommodate the reduced levels of air infiltration through the windows and doors.

If you don’t rebalance, negative pressures can be created within the building because the HVAC unit is still trying to draw make-up air from the existing spaces, yet there is less volume allowed from around the windows and doors. When the allowable air infiltration is reduced in volume, a higher pressure (negative) is created within the structure. That make-up air must come from someplace else, typically from other small holes or cracks in the building envelope. This can lead to whistling and howling noises and water infiltration in places that had never occurred in the building before, says Brenden.

3. When installing exterior glass doors in multifamily dwelling units, consider these building code pointers and cautions:

  • Doors must have a minimum clearance width of 32 inches (measured from the face of the door to the stop of the door while open 90 degrees) for wheelchair access.
  • Exterior door thresholds and sliding door tracks typically should not exceed ½ to ¾ inch high. Thresholds and changes in level at these locations are to be beveled with a slope no greater than 1:2.
  • Minimum clearance width for an accessible route inside the unit is 36 inches.
  • If a balcony or patio has doorways leading into two or more separate rooms, all doors must be wheelchair accessible.

Note: Always consult with the local building code official to determine the applicable code requirements.

4. Keep windows flush with the face in surface barrier applications. In surface-barrier wall systems that don’t include a water-resistive barrier behind the exterior skin, such as poured concrete walls or CMU without wall cavities, do not allow the windows to extend beyond the exterior face of the building or beyond the exterior water barrier.

“It’s imperative that sealant continuity be achieved between the drainage plane of the window/door and the adjacent construction,” says Brenden. “This crucial area forms the primary defense against air and moisture intrusion.”

5. Never take action inconsistent with the manufacturer’s installation instructions without consulting all appropriate parties. The manufacturer is most familiar with how the product should be installed to function properly and meet the terms of the warranty.

“Installation is not a one-size-fits-all solution,” says Brenden. Each product has unique design characteristics, including method of fabrication and assembly, hardware, sash operation and recommended maintenance. These factors often dictate how the manufacturer requires its product to be installed to meet its performance requirements.

6. Know when safety glazing is required. While not as common in residential construction, remodelers taking on commercial work would be well advised to heed the IBC 2003 rules governing safety glass. It is required in any operable window or fixed panel adjacent to a door where:

  • The nearest exposed edge of the glazing is within a 24-inch arc of either vertical edge of the door in a closed position
  • The bottom of the exposed edge of the glazing is less then 60 inches above the walking surface

Exception: Safety glass is not required when there is an intervening wall or other permanent barrier between the door and the glazing. In addition, it’s not required for glazing in walls that are perpendicular to the plan of the wall the door is in.

When designing rooms that include operable windows or individual fixed panels not adjacent to doors, safety glass is required where:

  • The exposed area of an individual pane is greater than nine square feet
  • The exposed bottom edge if the glazing is less than 18 inches above the floor
  • The exposed top edge of the glazing is greater than 36 inches above the floor
  • One or more walking surface(s) is within 36 inches horizontally of the plane of glass

Exception: Safety glass is not required when a protective bar 1½ inches or more in height and capable of withstanding a horizontal load of 50 lb. per linear foot without contacting the glass is installed on the accessible sides of the glazing 34-38 inches above the floor. In addition, it’s not required in the outboard lite in an insulating glass unit or multiple glazing where the bottom exposed edge of the glass is 25 inches or more above any grade, roof, walking surface, or other horizontal or sloped surface adjacent to the glass door.

This story originally appeared in our sister publication Building Design+Construction.

 

Avoid These Common Installation Mistakes

AAMA’s manufacturer members identified 40 common installation miscues. Here’s a summary of the most crucial:

  • Never block weep holes with sealant or any other material that will keep water from draining properly.
  • Don’t drill through window or door frames to apply alarm systems. Doing so may allow water to penetrate into places where it can’t get out.
  • Don’t apply film to the glass without first consulting the window or door manufacturer. Film may lead to heat buildup and glass breakage.
  • Don’t block the drainage path (weep holes) at doors when used in conjunction with patios involving brick, stone or concrete pavers. When necessary use a starter sill, or shim the door high enough to clear any obstructions.
  • Don’t block breather holes with sealant on dual-sash units. Breather holes are there to allow air circulation.
  • Be careful when welding after installation. Shield the glass and frame from weld flash to avoid damage.
  • Seal metal-to-metal joints. Also, make sure end dams are sealed properly on sub-sills.
  • Use compatible sealants that are meant to allow for movement due to expansion, contraction or displacement between stories. Also, know the sealant maker’s guidelines for maximum and minimum temperature when applying sealant.
  • Don’t use the finished window or door opening as an access for the delivery of materials. This often results in the build-up of debris inside the frame and can cause damage to window frames and door thresholds.
  • Make sure the framing surfaces are protected from corrosive materials such as mortar or sulfuric acid, which are commonly found in many external cleaning solutions.

AAMA offers advice to make sure key building components are chosen and installed properly


Add new comment

Plain text

  • No HTML tags allowed.
  • Web page addresses and email addresses turn into links automatically.
  • Lines and paragraphs break automatically.
leaderboard2 - default

Related Stories

Pella's New Debut Promises Faster, One-Person Window Installs

The window manufacturer promises 3.15x faster installation with its Steady Set system

Marvin Releases Switchable Privacy Glass Window

The privacy glass windows can be purchased from Marvin's Direct Glaze windows

Innovative Products: Window Shades That Create Natural Light

Wait, shouldn't window shades keep light out?

Pro's Pick: A Better Tool for Window Installs

This pro's pick is a big help for window and door installers

Andersen to Develop Solar Power Generating Products

The leading manufacturer will develop solar power generating window and door products in partnership with Ubiquitous Energy

Top 100 Products 2022

The industry's best, determined by our audience

Top 100 Products 2022: Windows & Doors

Products from Andersen, LaCantina, ProVia, Phantom Screens, and Windsor Windows & Doors

How to Replace a Window (Part 2)

This time it’s in a fat wall wrapped with a housewrap air barrier and exterior rigid insulation

Windows Go In at Model ReModel 2022

Symbi Homes selects custom black windows for its healthy, modern accessory dwelling unit

How to Replace a Window in a Fat Wall (Part 1)

Jobsite Know-How details how to install a window... again. This time it’s in a fat wall wrapped with an air barrier and exterior rigid insulation

Advertisement
boombox2 -
Advertisement
halfpage2 -
Advertisement
native1 -

More in Category




Advertisement
native2 -
Advertisement
halfpage1 -
Advertisement
leaderboard1 -