flexiblefullpage - default
interstitial1 - interstitial
Currently Reading

Repairing a Sinking Slab

Advertisement
billboard -
Jobsite Know-How

Repairing a Sinking Slab

High-density foam injected under a concrete pool patio raised cracked and sinking sections back to flush and level 


By By Niles Erickson March 30, 2018
raising a concrete slab by injecting high-density foam under it
This article first appeared in the April 2018 issue of Pro Remodeler.

Concrete slabs crack, sink and settle because of bad base preparation. My company recently used a system called PolyLevel (foundationsupportworks.com/solutions/polylevel.html) to repair a cracked and sunken slab surrounding a swimming pool. The repair involved injecting a high-density polyurethane foam to lift and support sunken sections of the patio slab to create an even surface.

The system is not strictly for patios and pool slabs. We’ve used it to raise interior residential slabs, and the density and expansive force of the foam can be adjusted and used to lift and stabilize large industrial slabs, and even roadways and airport runways. Here is a step-by-step description of the pool patio repair.

Install injection ports. In this case, the outer edge of the slab had dropped several inches, creating a large crack that ran almost the full length of the pool and causing reverse drainage at the house foundation. In other areas, a series of cracks created several independent sections of slab that had sunk to several different levels, creating dangerous trip hazards.

We drilled a series of ⅝-inch-diameter holes through the slab in a pattern determined by the area of the slab we needed to lift and how much we had to lift it [1]. The white areas on the slab are hole locations, which in this case were about 3 feet apart and about 18 inches from the edge of the slab. (We typically keep holes at least 6 inches from an edge; any closer and the foam tends to ooze out the side.) Each hole is fitted with a plastic port designed to receive the foam injection nozzle [2].

Inject the foam. Two separate liquids are pumped through separate hoses [3] to the injection nozzle [4], where they mix together. That triggers a chemical reaction that creates a high- density, expansive foam, which can be injected at temperatures above freezing, provided there is no frost in or under the slab.

Raising the slab. As the foam is injected [5A], the slab slowly rises until it is flush with the adjacent concrete [5B]. Controlling how much and how fast the foam expands depends on two factors. One is the chemical mix, which can be adjusted before it reaches nozzle; the other is the technique we use to inject the foam.

We begin injecting in short bursts to gauge how fast the foam is expanding and lifting the slab. The foam begins to stiffen quickly, but it doesn’t fully cure for 15 minutes, so there is a window of time in which to make adjustments and add more foam as needed. We’ve never had a problem with under- or over-filling, and over time we’ve developed several techniques that enable us to work to a tolerance of 1/16-inch. The simplest check is for the person controlling the nozzle to keep a finger or hand on the crack to feel when the surfaces are level with each other. In some cases, we also use a laser level to indicate when the slab has reached the desired height.

Caulk and cleanup. On this project, we drilled and injected one section at a time, working our way around all of the sunken areas of the patio [6]. After removing the injection ports, we sealed the holes with concrete, which leaves nickel-sized spots on the slab. We like to seal the cracks with Nexus Pro NP1 sealant to help keep water from passing through and getting under the slab, but we leave that decision to the homeowner. When we do seal them, we sometimes have to grind them a little to create a channel that’s wide enough to fill properly. 

Get more Jobsite Know-How here


This article was adapted from the video “How to Repair a Sinking Concrete Slab” at ProTradeCraft.com; the original video, Sinking Slab & Pool Patio Repair,” is one of many available at the Erickson Foundation Supportworks website.


Add new comment

Plain text

  • No HTML tags allowed.
  • Web page addresses and email addresses turn into links automatically.
  • Lines and paragraphs break automatically.
leaderboard2 - default

Related Stories

6 Must-Knows for Installing Pocket Doors

Save your sanity: Do it right the first time

Crawl Spaces to Basements: Proceed with Caution

Converting a crawl space to other uses can upgrade a home and add significant value, but when done incorrectly, it can also be disastrous 

The Ins and Outs of Pedestal Tile Systems

A non-exhaustive overview of all things pedestal tile systems

How to Attach a Patio Roof to an Existing House

A graceful integration may mean more work but improved functionality and aesthetics 

6 Tips for Electric Floor Heating Systems

These quick tips and tricks provide a base knowledge to begin your floor heating education

How To Improve Energy Performance in Existing Attics

There’s more to insulating the attic than attic insulation; there’s venting, air sealing, and misery

How to Install PVC Bevel Siding Over Rainscreen

It’s a lot like installing wood bevel siding, except it won’t warp or rot. And it expands and contracts differently and for different reasons

Understanding How PVC Trim Moves

Anybody who’s used PVC in an exterior application knows that it moves seasonally. Just like wood, right? Not exactly

To Vent or Not to Vent: A Discussion

In an attempt to strike a middle ground between high-performance and attainable, these three remodelers engage in a candid conversation

Diagnosing Cracked Concrete

These quick questions (and solutions) will allow you to determine if a crack is aesthetic or structural

Advertisement
boombox2 -
Advertisement
halfpage2 -
Advertisement
native1 -

More in Category




Advertisement
native2 -
Advertisement
halfpage1 -
Advertisement
leaderboard1 -